Skip to content

CDP ​

在規劃一個網路架構時,如果不小心失去網路架構的資訊,應該會造成管理上的混亂,如果該環境設備都是 Cisco 設備,則可透過 CDP 協定探索收集到全部 Cisco 網路設備的軟硬體資訊,立即重建網路拓樸資訊。

利用 CDP 協定交換資訊 ​

Cisco 網路設備會定期與周遭的 Cisco 網路設備進行資訊交換的動作,要達到這樣定期的資料交換動作,就必須透過 CDP 協定才行。CDP(Cisco Discovery Protocol)是 Cisco 的專利,運行於 OSI 七層協定之中第二層 Data Link Layer 的協定。可以透過它來讓設備相互收集設備的資訊,如:ISO 版本、IP 位址等。

CDP 協定所提供的資訊 ​

  • 設備ID
    • 設備的名稱
  • 第三層的IP位址清單
    • 來源端和目的端埠名稱,例如:ethernet0
  • 埠的ID
  • 所支援的功能列表
  • 硬體平台
    • 硬體型號

關閉或開啟 CDP 協定的指令 ​

以下範例拓樸圖

開啟或關閉 CDP ​

bash
R1(config)#no cdp run
R1(config)#cdp run

關閉或重啟某介面的 CDP ​

bash
R1(config-if)#no cdp enable
R1(config-if)#cdp enable

CDP 協定的設定方式 ​

顯示CDP協定資訊的指令 ​

Cisco 路由器上的 CDP 協定可以開啟或關閉,預設為開啟。

bash
R1#show cdp 
Global CDP information:
    Sending CDP packets every 60 seconds
    Sending a holdtime value of 180 seconds
    Sending CDPv2 advertisements is enabled

CDP 指令 ​

環境是以 Packet tracer

bash
R1#show cdp ?
  entry      Information for specific neighbor entry
  interface  CDP interface status and configuration
  neighbors  CDP neighbor entries
  traffic    CDP statistics

CDP neighbor entries ​

bash
R1#show cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater

Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID
R2               Ser 3/0            166           R       7206VXR   Ser 3/0
ESW2             Fas 0/0            166          S I      3745      Fas 0/0
  • Device ID
    • 鄰近設備的 ID
  • Local Intrfce
    • 本地端的介面
  • Holdtme
    • 設備持有目前資訊長達多久的時間
    • 單位是秒
  • Capability
    • 鄰近設備的種類代碼
  • Platform
    • 鄰近設備的硬體平台
  • Port ID
    • 鄰近設備的遠端埠ID

鄰近設備的種類代碼 ​

設備代碼意義
RRouter
TTrans Bridge(Ethernet 架構)
BSource Route Bridge(Token Ring 架構)
SSwitch
HHost
IIGMP
rRepeater
PPhone

取得更詳細的資訊 ​

bash
R1#show cdp neighbors detail
-------------------------
Device ID: R2
Entry address(es):
  IP address: 192.168.1.254
Platform: Cisco 7206VXR,  Capabilities: Router
Interface: Serial3/0,  Port ID (outgoing port): Serial3/0
Holdtime : 126 sec

Version :
Cisco IOS Software, 7200 Software (C7200-ADVENTERPRISEK9-M), Version 12.4(24)T5, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Fri 04-Mar-11 06:49 by prod_rel_team

advertisement version: 2

-------------------------
Device ID: ESW2
Entry address(es):
  IP address: 192.168.100.10
Platform: Cisco 3745,  Capabilities: Switch IGMP
Interface: FastEthernet0/0,  Port ID (outgoing port): FastEthernet0/0
Holdtime : 126 sec

Version :
Cisco IOS Software, 3700 Software (C3745-ADVIPSERVICESK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 18-Aug-10 08:18 by prod_rel_team

advertisement version: 2
VTP Management Domain: ''
Duplex: half

特定鄰近設備的相關資訊 ​

參數

bash
Router#show cdp entry ?
  *     all CDP neighbor entries
  WORD  Name of CDP neighbor entry

指定某台設備

bash
R1#show cdp entry R2
-------------------------
Device ID: R2
Entry address(es):
  IP address: 192.168.1.254
Platform: Cisco 7206VXR,  Capabilities: Router
Interface: Serial3/0,  Port ID (outgoing port): Serial3/0
Holdtime : 138 sec

Version :
Cisco IOS Software, 7200 Software (C7200-ADVENTERPRISEK9-M), Version 12.4(24)T5, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Fri 04-Mar-11 06:49 by prod_rel_team

advertisement version: 2

顯示的資訊

  • 鄰近設備的Device ID
    • R2
  • 網路第三層協定的資訊
    • 192.168.1.254
  • 鄰近設備的硬體平台
    • Cisco 7206VXR
  • 鄰近設備的種類
    • Router
  • 本地端介面種類和outgoing遠端的埠ID
    • Serial3/0, Serial3/0
  • Hold-time值,單位是秒
    • 138
  • Cisco IOS軟體種類和版本資訊
    • Cisco IOS Software, 7200 Software (C7200-ADVENTERPRISEK9-M), Version 12.4(24)T5, RELEASE SOFTWARE (fc3)...

鄰近設備的種類可以顯示出這設備是 Route、Switch 或是其它種類的設備。

顯示目前傳送CDP的介面狀況 ​

指定 Serial 介面

bash
R1#show cdp interface s3/0
Serial3/0 is up, line protocol is up
  Encapsulation HDLC
  Sending CDP packets every 60 seconds
  Holdtime is 180 seconds

可得到的資訊

  • 介面是否運作中
    • FastEthernet0/0 is up
  • 每隔多久送出CDP封包(預設是每隔60秒)
    • Sending CDP packets every 60 seconds
  • Hold-time
    • 180 seconds(預設)
  • 封裝種類
    • HDLC

顯示與介面的流量相關的資訊 ​

bash
R1#show cdp traffic
CDP counters :
        Total packets output: 36, Input: 35
        Hdr syntax: 0, Chksum error: 0, Encaps failed: 0
        No memory: 0, Invalid packet: 0, Fragmented: 0
        CDP version 1 advertisements output: 0, Input: 0
        CDP version 2 advertisements output: 36, Input: 35

顯示資訊

  • 資料錯誤
  • Checksum錯誤
  • 封裝失敗
  • 記憶體用盡(Out of memory)
  • 無效的封包
  • 已分割的封包
  • 已經送出和已經接收到的 CDPv1 封包
  • 已經送出和已經接收到的 CDPv2 封包

清除 CDP traffic 相關資訊 ​

用來把 CDP 的 traffic counters 歸零

bash
R1#clear cdp counters
R1#show cdp traffic # 驗證
CDP counters :
        Total packets output: 1, Input: 0
        Hdr syntax: 0, Chksum error: 0, Encaps failed: 0
        No memory: 0, Invalid packet: 0, Fragmented: 0
        CDP version 1 advertisements output: 0, Input: 0
        CDP version 2 advertisements output: 1, Input: 0

清除 CDP neighbors 相關資訊 ​

將 show cdp neighbors 資訊清除

bash
R1#clear cdp table
R1#show cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater

Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID

設定 CDP Timer 和 hold-time 值 ​

CDP 資訊的交換頻率預設為 60 秒交換一次

改變 CDP Timer 將交換 CDP 的頻率改為每隔 65 秒交換

bash
R1(config)#cdp timer ?
  <5-254>  Rate at which CDP packets are sent (in  sec)

R1(config)#cdp timer 65
R1(config)#do show cdp
Global CDP information:
        Sending CDP packets every 65 seconds
        Sending a holdtime value of 180 seconds
        Sending CDPv2 advertisements is  enabled

變為預設 60 秒

bash
R1(config)#no cdp timer
R1(config)#do show cdp
Global CDP information:
        Sending CDP packets every 60 seconds
        Sending a holdtime value of 180 seconds
        Sending CDPv2 advertisements is  enabled

通常要更改 CDP 的發送頻率都是因為頻寬的考量,因此可以根據所使用的環境來設定適合的發送頻率。

改變 hold-time

改為保存 200 秒 CDP 設備資訊

bash
R1(config)#cdp holdtime 200
R1(config)#do sh cdp
Global CDP information:
        Sending CDP packets every 60 seconds
        Sending a holdtime value of 200 seconds
        Sending CDPv2 advertisements is  enabled

還原預設

bash
R1(config)#no cdp holdtime 200
R1(config)#do sh cdp
Global CDP information:
        Sending CDP packets every 60 seconds
        Sending a holdtime value of 180 seconds
        Sending CDPv2 advertisements is  enabled

hold-time 表示 Cisco 設備要在本地端保留其他設備的 CDP 資訊長達多久的時間,預設值為 180 秒。

VLAN 與 CDP ​

通常預設的 VLAN 都是 VLAN 1,因此,CDP 和 VTP 協定的封包通常都會送到 VLAN 1 之中。

參考資料 ​

Jan Ho

Built with VitePress